人妻侵犯一区二区三区乱码图片,国产av毛片,欧美日韩中文国产一区发布,色综合99久久久无码国产精品

泰安揚帆數控科技有限公司為您提供等相關信息發布和資訊展示,敬請關注!
咨詢服務熱線:
13345281377

新聞資訊

產品

自動焊接設備在焊接過程中容易出現哪些問題?

來源:http://camtask.com/  發布時間:2021-05-10 瀏覽次數:0

一、自動焊接設備焊接時會產生焊縫夾渣,主要有以下三個方面的原因造成的:

1、 There are three main reasons for slag inclusion in welding seam when automatic welding equipment is used
1、打底焊后不徹底,致使在快速熱焊時,未能使根部熔渣完全溢出。
1. After the backing welding is not complete, the root slag can not completely overflow during the rapid hot welding.
2、打底焊清根的方法不當,使根部焊道倆側溝槽過深,呈現W狀。在快速熱焊時,流到深槽的熔渣來不及溢出而形成夾渣。
2. The improper method of backing and root cleaning makes the groove on both sides of root pass too deep and W-shaped. In rapid hot welding, the slag flowing to the deep groove has no time to overflow and form slag inclusion.
濟南自動焊接設備
3、在仰焊位置收弧過快也易產生夾渣。
3. In overhead welding position, too fast arc stopping is easy to produce slag inclusion.
二、自動焊接設備焊接過程中產生氣孔的原因:
2、 The causes of Blowholes in the welding process of automatic welding equipment are as follows
1、蓋面焊時,熔池過熱,吸覆大量的周邊空氣。
1. During the cover welding, the molten pool overheats and absorbs a lot of surrounding air.
2、蓋面焊時,焊條擺動幅度太大,熔池保護不佳。
2. During the cover welding, the swing range of welding rod is too large, and the protection of molten pool is poor.
3、根部間隙過小,容易產生根部針形氣泡。
3. If the root gap is too small, needle shaped bubbles are easy to form at the root.
4、焊條未在規定時間內用完或長時間暴露在空氣中。
4. The welding rod is not used up or exposed to the air for a long time.
三、焊縫產生裂紋的原因
3、 Causes of weld cracks
1、如果施工地段起伏較大,土墩未及時墊到位,使管子處在受力狀態,在焊接收弧點,尤其是6點鐘位置易出現應力裂紋。
1. If the construction section fluctuates greatly and the soil pier is not padded in place in time, the pipe will be in the stress state, and the stress crack is easy to appear at the welding stop point, especially at the 6 o'clock position.
2、在焊接過程中,如果早松開或撤離對口器,致使熔池中的鐵水未來的及凝固好,在焊接收弧出容易產生裂紋。
2. In the welding process, if the aligning device is released or withdrawn early, the molten iron in the molten pool will solidify well in the future, and cracks are easy to occur when the welding arc stops.
3、焊工在仰焊位置采用直接熄弧等不當?shù)氖栈》椒ǎ率谷鄢匚刺顫M形成弧坑而出現弧坑裂紋。
3. The welder adopts improper arc stopping methods such as direct arc extinguishing at overhead welding position, which leads to the formation of crater cracks due to the incompleteness of molten pool.
四、自動焊接設備焊接時內凹產生的原因
4、 Causes of concave in automatic welding equipment
1、打底焊時熔透深度不夠。
1. The penetration depth of backing welding is not enough.
2、焊接電流過大,熱焊時在5-7點位置焊速太慢。
2. The welding current is too large, and the welding speed is too slow at 5-7 points during hot welding.

上一篇:焊接機器人與焊接專機的不同及其外部軸的作用
下一篇:如何選擇自動焊接機器人的工件附件呢?

久久av一区二区三区漫画| 免费一级片在线观看| 最新国产av| 色欲AV伊人久久大香线蕉影院| 国产福利在线视频| 国产精品乱码一区二区三区| 91人妻人人澡人人爽人人精品6| 日产精品久久久久久久性色91| 精品国产乱码久久久久久蜜柚| 久久99国产精品1区二区| 免费av在线| 国产尤物av| 少妇人妻系列1~100| 国产精品视频一区二区三区| 热热色| 成人亚洲精品久久久久软件| √天堂资源在线三四区| 亚洲毛片在线播放| 91精品国产91久久综合桃花| 91麻豆精品国产91久久久无限制版| 内射人妻少妇| 97在线视频观看| 成人欧美一区二区三区黑人麻豆| 尤物av在线| 午夜福利短视频| 肉大捧一进一出免费看| 天天干天天日天天草| 久久久久久久av麻豆果冻| 欧美大荫蒂毛茸茸视频| 丁香花在线免费观看高清视频| 欧美人妻一区二区三区四区五区| 国产精品福利在线| 亚洲av永久| 欧美精品一区二区三区蜜桃视频| 精品久久久久久久久久久国产字幕 | 精品视频在线观看一区二区| 国产精品剧情在线观看| 国产麻豆成人a| 亚洲av最新| 国产欧美精品一区二区色综合| 亚洲精品污一区二区三区|